Search results for query: grommet

...the tag on the loom, that loom crosses the tunnel so I just moved it out of the way whilst drilling for the heater instal , then I split the grommet installed all the extra looms, popped it back in then sealed it. Took 6 hours to fit the heater (two of us, neither having done it before but...

...7LA 971….(whatever the rest is) into Google and it may give you an idea what it’s for. Heated or electric seats maybe? You could maybe disconnect it (once you know what it is) and move to one side while you do the hole then re-reroute it alongside the pipe with a suitable grommet and protection.

Thanks, I decided to take a look tomorrow when its on the ramps, seemed sensible. I think the van was almost a virgin when I got it @ 2000 miles so I suspect the wire is factory or linked to perhaps a factory options fitted.

The dome nut is an earthing point. Nothing connected to that underneath. I can't remember a wire going through that rubber grommet on mine. But it doesn't look OEM to me (but I could be wrong on that).

...a 64mm hole through the floor for the 'Hot Air in' pipe and the floor looks subtly different to the videos I've seen, they show an unused grommet, where I have one with a wire going through it, and the vids also show an empty 7mm ish hole where I have a dome nut. I'm guessing there is...

...simple - you will need the following: Short cable from Starter battery (SB) to a 60a midi fuse then cable to the DC-DC pos input there is a grommet behind the SB into the cabin. Neg from DC-DC to chassis ground point (there are ones under the seats) or a neg busbar. DC-DC pos output to a...

Thanks, I'll look into this.

...These are plug and play. 4300k give the best light output. There is a lot of gubbins that sits outside on the headlight. Use a £1 coin as a template to cut a hole in the rubber cover in the back of the headlight and the grommet in the loom will fit perfectly in it.

I had the same problem today! I was at a shopping centre and put some bags into the van. Unfortunately my jacket somehow got caught between the van and the door and got trapped I could not open the door from either the inside or outside so had to drive home with the jacket stuck Your advice...

Ah ok found a grommet quite high up past the servo area but because it is a LHD it does come behind the glove box, well further up. How’re I past a guide but cannot see it so I guess it would be best to remove the glovebox or just the bottom plastic cover. It all seems so difficult to remove.

I really like this. Much preferred set up compared to drilling into the van body.

...240v cable can then be earthed easily at engine bay and then routed through the bulkhead and into the van near to the seats - as there's a grommet here to go through. Is this what you have done on your van? I have also seen a method where the VW badge opens up and a socket is installed under...

Hi is this not a drain also ? Just worried before I go plug a hole in it and cause a problem

I had someone to do that for me when I bought the van new Ithink they brought it out of the bulk head grommet behind the battery and down behind the dashboard and under the carpet and they fitted the dc to dc charger under the drivers seat.

...have swivels on both seats). I would run new cables if at all possible. The one from the starter battery is pretty easy through an existing grommet (you will be able to see it down behind the battery - probably with the existing cable through it) and under the cab floor covering. It’s easier...

...to see in to the panel from underneath to see if there's a loom that I could unplug but no addition loom it seems. The cable runs through a grommet above the shied and the light cluster cable plugs in to it inside the panel. Also checked the connectors under passenger seat, the blue block...

...cover, rubber O ring for fuel return on injector. 2x stretch bolts used on the 2x injector clamps need renewing. The bolts have sealing grommet on rocker cover. Manual states to renew if damaged, but taking the view more cost efficient to just renew. VW van centre 1 is quoting ~£870 for job...

Ok that’s great thanks, yes I’ve now seen an existing grommet to the scuttle so might use that instead. Cheers

...I’d void the warranty if I drilled through them so I’m moving the mounts up the rail slightly so I only have to drill through the fibreglass. Just waiting for the rubber grommets to arrive that’ll plug the holes i dont use! As always, the jobs a bit more involved than it first appeared haha.

@Richard85 I tried those self adhesive cable tie pads on the painted body under my vans tail lights to secure some water tank vent tubes. Even with a thorough cleaning they don’t stay stuck for long. You may have to find a different way to secure the conduit.