Search results for query: grommet

Ordered piggy back spade connector and grommet. What wire would I need to ground? What connectors? Presume heavy on silicone in any drilled holes?! Really excited if I can access under shelf void! Game changer that possibly! Many thanks again.

Hence why I was trying to get quotes for someone to do this?!

And presume if I forsake the ‘curly cable’ solution to rear tailgate grommet, I would simply drill into pop top, install gland etc before entering wire at rear of canvas current Velcro and then drilling into top of rear wardrobe unit?

Here's a couple of ideas. So much info on this on various threads. Bit of a minefield! Took me a while to work out how I was going to do it. I've ran mine through the velcro at the back same as the second set of pics. Another solution in the first set of pics

...I could have soldered, but idk, seemed like a solid connection then wrapped with Tesa loom tape. I then routed the wire through the rubber grommet on the side of the ebox, and sleeved it to protect it. Routed it round the back of the battery and firewall and master cylinder the down back of...

Got it mate. Thanks for getting back to me! I’ll have a crack at this tomorrow.

You should be able to pull back the rubber floor matting which goes over the wheel arch and then behind this you will see a black grommet. Pull that out and you will get to the inner bolt.

Hello I am planning on running the EHU cable and the B-2-B cable from the engine bay through the grommet in the bulkhead. I would then like to use the cable run that is on the left hand side of the drivers footwell. I have looked at the instructions about lifting the rubber floor and can see...

Passenger side up top - open the tailgate and you will see the grommet/bellows

I had this problem on one of my T5's and it was the rubber grommet for the hole for the sliding door motor which my van didn't have, new bung and some sealant sorted it.

...for the fresh and grey water, and fittings/clamps etc. I went for the 16l one with the premium pump and integrated lid which has the rubber grommet for the wire and a one way valve for air, and fittings for the 10mm fresh water hose. £95 all in. Really good quality thick grey and fresh...

Set of SWB roof bars (made by Omtec). Few years old but only fitted for 1 of those, been in the garage since. Odd mark from normal usage but great condition. Comes with all mounting feet, spacers, bolts and blanking grommets. £35 collect from Wolverhampton area.

...tweeter wires in the pillars. door speakers were housed on vauxhall collars, plugs chopped off, wires routed through the window regulator grommet and already were corroded. wires were twisted with no proper connection ti on or solder joint , used coax speakers ! they broke the clip holders...

Yeah that is of slight concern. I think regs is 2m and I’m at about 3 ish. But it’s through grommets, and routed through channels so minimal chance of rub and nowhere it can be trapped or cut. FYI I’ve just stripped the cab out for another issue and the 240 cable is as new. It routes out of the...

Will take a look does this mean lifting the seat or getting under the van It doesn’t feel like a draft it is more like a cold bridge I can’t feel any sort of draft it’s more radiant cold off the seat base That’s why I think it’s cold bridge? But anything worth a try is there only one point...

There are wiring grommets under the seat under the flooring, is it possible that one of those has fallen out?

...or inside. So here's what I did as temp and then permanent fix. Temp fix - on inside just above the latch in centre of tailgate is a rubber grommet. Remove to expose latch mechanism. You will see the latch bar. Pull this up to open the door. Close door, drive home. The actuator may unlatch it...

...from being the light switch. Dead easy At this point I was feeling good about the job and preceded to run the new wire to the E box through a grommet in the bulkhead on the drivers side and across the engine bay to the passenger side, all neat and tidy cable ties along the way. Battery out...

...are some possible adjustments down there. Also check all the various bolts are tight - I found a couple of loose ones. On mine there was a grommet popped out where the locking lever went through a frame. I still have a couple more squeaks to track down though. Battery - if this is original...

Thanks Sipep. Anybody else know if there is any advantage to using the grommet behind the air box rather than the one behind the battery for cable entry to run to under the drivers seat, is their channels under the rubber mat this side of van.