bed

I love a bit of upcycling! Build inspired by the Amdro folding bed. Re-purposed an old Futon that was collecting dust in our shed (a good day of hard sanding!). Some left over scaffolding poles & attachments I had after building my computer desk. Harness straps hold the bed securely to the...

My requirements were a mattress which could go flat / be left in roof space / fit the space when inflated / be comfortable / cheapish but comfort a priority so......., I have found this 200x120x17cm inflatable bed - yes inflatable not self inflating so I can deflate to nothing. It’s flocked...

Hi, I've had a Cambee Flex 3/4 bed on rails fitted, which is great. However, once I've built the furniture from an Evo kit and fitted it alongside, the bed is really difficult to move along the rails. I've carpeted the interior but still have ply panels to fit on the furniture side, but if I do...

I've got a kombi with swivel seats and the rear bench and realised that I can lie flat (I'm 6ft) if the seats are swivelled, pushed as close to the dash as possible, and my feet are pointing towards the passenger wing mirror and my body is diagonally across the seats so my head is on the drivers...

Hi New to the forum and just bought a long awaited t6 LWB van with the plan of making into a camper over the next 12-18 months. Summer is here (well its not raining right this minute!) so I would like a few trips this summer, even if it is in very basic panel van mode. First job will be to...

i have just bought a high line kombi SWB and will be attempting a mild conversion, so will have loads of questions !! Looking forward to everyone’s advice

Hi All, There are some companies doing Rib seat covers...@ £150 :rofl: Does anyone know of any reasonably priced ones?

I decided that I wanted the bed positioned as far back as possible, and with the bed frame bolted to the chassis cross members. There are many different ways to do this installation, this is my way, it may not be the "approved" way.

im after buying a 112cm 2 seater rib bed but I've looked on a website and it looks like you actually lie on the back of the bed? Does the back have a soft matteress on it or will i need to buy a matteress for it ? Seems lot of money if i have to buy something to lie on aswell?

Exciting times... I'm finally pushing on with the process of getting my Kombi ready for using as a 'day van' in the summer... It's already insulated and lined (by Leighton Vans) but I'm yet to do other bits. The next step is heading down to 'Forty Winks' tomorrow, to have a Kombi Bed fitted...

Can fit 2 of either of these side by side in rear if needs be. Pack down tiny too.

to get the rear 2+1 seats in a Kombi to recline fully?, or whether they are purely fixed in a single seating position? i have looked through the forum, but cant find anything on if its possible? many thanks kris

Hi all , just a little advice if I can , I’m looking to add a bed / seat system to my kombi , I really like the idea of Cali rails and a 3 seater caravelle seat that will fold to a bed with the flexi board , but have also seen the rock and roll beds on rails I like the look of the Reimo varitech...

Anyone got recommendations for rock and roll beds. Not a fan of RIB beds. Have been looking at JAC conversions (super cheap) but pull tested and for 1000 quid comes retrimmed in leather Rusty lee- but can see if there pull tested Also looking at Blade beds but seem quite narrow . Any input...

Got to love this forum, so much infomation to be had thank you Mr T6 forum owner and the Admin who run it. I needed a parcel shelf that would cover my tools and stop then being seen from outside, but it also need to allow me access to the tools when working from the van... after a bit of...

We have a wonderful T6 with a pop up but are struggling with the thin foam mattress - ideally would like one which we can leave up when we close the pop up but open to all suggestions and recommendations please Thanks guys!

Hi! We have a blank canvas and are discussing the pros and cons of fitting floor rails so we can move the seat/bed forward and back. We've heard they're a real hassle to fit and we want to know whether there's an easier product to fit or even if they are worth the hassle? Any recommendations?

Does anyone have an Autoglide bed? been looking and they look a decent bit of kit, open to other recommendations looking to mount it on a Koller fully bonded floor Thanks

Hi, just looking for any advice regarding converting a T6 shuttle to a camper. Does the rear heater/air con unit and roof lighting cause an issue if removed to fit pop top etc. Anyone?

Looking for T6 SWB conversion using 1300mm bed where the end cabinet (fridge) doesn't protrudes 400mm from the furniture run into the cabin, I have seen 1 conversion I really like but it is 325 miles away from where I am in the North West, I have called few local converters and they all give...