seat base

Hi I've bought this battery GB12115 - Battery Service Hub But I've been told it wont fit? Is there any way i could make it Dimensions length 331 x width 176 x height 220 mm

Are T5 and T6 front single seat bases the same?

So annoyed with myself. Rejigged all the electrics under the drivers seat. Put the drivers seat back on and the 2 wires out the top of the ctek foul a bar under the seat. Any thoughts as to cutting away the insulation on the ctek sense wires and making god with hot glue or do I need to move the...

Just finished installing the ctek and battery etc. I thought it would be easy to make it look neat. With loads of room. Nope. Awkward af. And advice on how to tidy up this nest of cables? Thanks

Hi All. I was wondering if its very bad practice to place the inverter under the driver seat? I don't know if theres room yet. I have a battery, fusebox and ctek 250se. Or would it be best placed under my passenger seats? I have a double. Im only looking at a small inverter to run a laptop...

ANYONE KNOW THE PART NO. FOR THE PLUG THAT GOES IN TO THE LIGHT or were to order from THANKS

Hi all , I am fitting a diesal heater to my T6 campervan and want to remove the front passenger seat. Should I disconnect the battery before unplugging under seat connectors as I have a side airbag in the seat and dont want to set it off .

Drivers seat base with lowered handbrake bracket to clear RIB seat swivels without spacers. (Might fit other swivels but not tested) The handbrake bracket has been drilled off and rewelded about 25mm lower than standard. This clears the RIB swivel seat with a standard cover fitted and keeps the...

Trying to hardwire my Blackvue battery that is under passenger seat. I got positive supply from fuse box. And found a suitable earthing point on the seat base. It has continuity to earth. i.e I am find it with a multi meter in any metal part. But I am not getting a power feed due to no 12...

I have a general build thread in the works (Our T6 build journey...complete beginners!) but starting a separate thread for the electrics so that people can tell me in one place if i'm going to set my van on fire. After much research and deliberation we decided to go the lithium route with our...

Has anyone had the weld for the nut under the drivers seat that connects it to the black base come loose? I am trying to loosen the bolt to get the top of the seat off but it just keeps spinning and I can't get in to get a decent hold on it to sort it. Any thoughts?? :(

This week, I bought 2x 130Ah Valence Lithium Iron phosphate batteries, and some (but not all) of the Victron kit I need. I've also spent loads on tools ( I love buying tools), the hydraulic crimp tool is great!! Please see the diagram below, I think this is pretty much as it should be, and I...

A pair of VW single seat base plastic covers. Came off my Kombi when I converted to a camper. £10 for the pair. I'm near Sevenoaks in Kent, collection please.

Having a clear out of my garage. Original VW single passenger seat base. £20. I'm in Kent near Sevenoaks J5 on M25. Collection only as would be a pig to package up and post. £20.00

Does anyone know if there is anyway of making the driver seat slide back further than the standard limits. is there any mods than can be done or alternatives parts that can be fitted. only need it to move back a few more inches.

Have anyone fitted/ have experience of using this sliding double seat base? I'm keeping the double chair setup for the moment, and like the idea of being able to bring another two seats closer to the table, if you need to be inside, (cold/ wet/ playing cards etc...).

Morning! Installed my leisure battery under my seat with a split charging system (CTEK) other than those items with an isolation switch (accessible from the under the front of the seat) there is not much room for anything else, so far so good. I need to bring that power out and will distribute...

I've lowered the handbrake to accommodate swivel bases on both front seats. In the process I did a butcher's job on the cover and now it's time to tidy it up. Does anyone know where I can find a new cover for a lowered handbrake?

Pic for clarity. Anyone used them? How strong is the magnet? I don't want them falling off under normal use! I think I'll be able to get the Erberspacher outlet to look nicer than i can using the OEM plastic jobby.

Fitting RIB offset swivels and want to keep the seats as low as possible so I am modifying the handbrake bracket so that I don’t have to fit the spacers that came with the RIB swivels. No problem drilling out the original spotwelds and grinding off the short weld on the back corner of the...