Retrofitting Xenon headlights T5.1

Gemo

New Member
Hi everyone
Please delete if this is not allowed here.
I was hoping to retro fit Xenon headlights to my T5.1.
I understand I need to fit front and rear level sensors. A headlight range control module and auto lights and rain sensors with different headlight switch aswell as a upgraded BCM.
I understand that Kufatec offer a adapter loom to go between the halogen
plug in the existing wiring loom to the Xenon socket in the xenon headlight
unit.
I understand you need to add two additional wires to the Kufatec harness to get it to work correctly.
I was thinking of if buying an Vw genuine Xenon headlight wiring
loom,7E0971114AN with fog lights and PDC option instead of the Kufatec
adaptor.
The loom will cost me about 150 euros and the Kufatec will cost me with
import duties about 70 euros.
I was thinking the wiring loom would dramatically reduce the wiring issues
and dramatically ease the installation.
What do you all think ?
Thank you in advance for taking time to read my post.
 
Kufatec do a loom for 5.1 so you shouldnt need to add anything, its the T6 retrofit that uses more cables so if you start with a 5.1 kufatec loom you have to add more wires to fit it to a T6
 
I have Xenon lights, my original BCM (running a T6 BCM now) has the following details : Part No SW: 7H0 937 090 D HW: 7H0 937 090
 
As an alternative approach, you could consider an aftermarket LED projector upgrade to your headlamps.
I have recently completed LED projector installation on OEM H4 T5.1(2015) headlamps for a friend of mine.
I bought a pair of universal LED projectors. I think it was from eBay and the cost was around €150 = £131.
Removal of the headlamps, splitting them in half, putting projectors in place of H4 bulb and the whole reassembly took me a total of 4 hours.
I was so surprised how easy it is to separate the front lens from the rest of the headlamp. No heat gun was required, just one pretty big flat screwdriver, one prying tool and sharp blade. Just started in the top inner corner of each lamp and it went extremely easy.
20220916_105444.jpg
20220916_105453.jpg

Projectors were also equipped with quite cool DRL rings. It is hard to judge the effect from photos taken in full daylight, but have a look below.
20220916_112650.jpg
20220916_112639.jpg

The projector kit includes few adapters/washers and the actual projector fits in the place of the H4 bulb literally like Plug & Play.

My friend didn't want to upgrade his BCM and unfortunately there was no way to adjust coding (on his BCM) to allow low beam to stay ON when high beam was ON.
As a solution, I have used one relay per headlamp to feed low beam while high was ON and simultaneously isolate the original low beam supply.
Basically, I didn't want to cut the wiring outside the headlamps and run any extra wires in between the headlamps.
Final result looks like OEM, externally there is not a single indication of anyone tampering with the headlamps.

20220917_094720.jpg
20220917_094657.jpg

Some final results at night.
IMG-20220916-WA0020.jpg

Plus the night test drive.
 
  • Like
Reactions: mmi
So I have got my xenon headlights all set up with the correct bulbs in every lamp. I have tried a quick test using the Kufatec xenon to halogen wiring loom adaptors.
I have got everything working. The xenon works in both low beam and the gate lifts to give me high beam. High beam second lamp works so does the indicator. The only thing that does not work is the DRL led bulbs. Is this normal.
 
If it’s retrofitter correctly it will operate as per factory so I guess if you are confident in your wiring and parts then it’s probably a coding error
 
Hi all, new here and a complete newbie when it come to Transporters so need a bit of help/guidance please

I have a 2012 T5.1 sportline with factory xenon headlights, ordered some of the Transporter HQ V3 LED headlights but they don’t seem to be compatible?

Could they be installed with an adaptor (if such a thing exists) or would they require a wiring change/programming as the sockets don’t marry up?

Thanks
 
Herkese merhaba
Eğer burada buna izin verilmiyorsa lütfen silin.
T5.1 aracıma sonradan Xenon far takmayı umuyordum.
Ön ve arka seviye sensörleri takmam gerektiğini anlıyorum. Bir far menzil kontrol modülü ve farklı far anahtarına sahip otomatik ışıklar ve yağmur sensörleri ve ayrıca yükseltilmiş bir BCM.
Kufatec'in halojen ile rezistans arasında geçiş yapmak için bir adaptör tezgahı sunduğunu duydum.
Mevcut kablo demetini xenon farındaki Xenon soketine takın
birim.
Kufatec kablo demetinin düzgün çalışması için iki ek kablo eklemeniz gerektiğini duydum.
Orijinal bir Vw Xenon far kablolaması satın almayı düşünüyordum
tezgah,7E0971114AN sis farları ve Kufatec yerine PDC seçeneğiyle
adaptör.
Tezgah bana yaklaşık 150 avroya mal olacak ve Kufatec bana şu kadara mal olacak:
ithalat vergisi yaklaşık 70 avro.
Kablo demetinin kablolama sorunlarını önemli ölçüde azaltacağını düşünüyordum
ve kurulumu önemli ölçüde kolaylaştırır.
Siz ne düşünüyorsunuz?
Yazımı okumaya vakit ayırdığınız için şimdiden teşekkür ederim.e
 
Herkese merhaba
Eğer burada buna izin verilmiyorsa lütfen silin.
T5.1 aracını sonradan Xenon far takmayı umuyordum.
Ön ve arka seviye sensörleri takmanın uygulanması. Bir uzak menzil kontrol modülü ve farklı far anahtarına sahip otomatik ışıklar ve yağmur sensörleri ve ayrıca tasarlanmış bir BCM.
Kufatec'in halojen ile rezistans arasında geçiş yapmak için bir adaptör tezgahının duyulduğu duyuldu.
Mevcut kablo demetini xenon farındaki Xenon soketine takın
birim.
Kufatec kablo demetinin düzgün çalışması için iki ek kablonun kaydedildiği duyulur.
Orijinal bir Vw Xenon far kablosunu satın almayı başarmak
tezgahı,7E0971114AN sis farları ve Kufatec yerine PDC seçeneğiyle
adaptörü.
Tezgah bana yaklaşık 150 avroya mal olacak ve Kufatec bana şu kadara mal olacak:
ithalat vergisi yaklaşık 70 avro.
Kablo demetinin kablolamanın önemli ölçüde azaltılabileceğini
ve kurulumu önemli ölçüde değiştirir.
Sen ne yakarsın?
Yazımı harcadığınız zamanı ayırdığınız için teşekkür ederim.
Merhaba, 2013 Caravelle aracım var. Bu konuda yardıma ihtiyacım var. Parça numarası ve kodlama konusunda bana yardımcı olabilir misiniz?
 
Back
Top