bulkhead

Hi Guys I have a Kombi Bulkhead available from my 2019 twin sliding Kombi, removed due to fitting Ovano unit, collection PE13 area Norfolk/Cambs Offers around £150 if any use to anyone?

Carpeted plywood bulk head and rear shelf. It’s in my SWB T6 Kombi, Was in the van when I bought it. £40 pick up from Southampton

I’ve removed this bulkhead the other week. It’s in really good condition though there is a hole cut out to allow ladders to be put in the Kombi via removing the +1 seat It has the vision panel fitted too. Collection from Clevedon (North Somerset).

Just removed bulkhead from my T6 van. metal two part collection only Bedford

Very light use in my LWB twin slider. May fit other models. Located near Havant Hampshire.

Im going to remove the top half of my bulkhead and wondered if i will need a wider roof trim strip between the cab headlining a roof board? I know the roof board sits above the bulkhead but i imagine there is going to be a gap between the trim covering the bulkhead cab bolts and the roof board...

Hello All, I have a Motexion bulkhead for sale looking for £175 or nearest offer . We are getting a poptop so this Kombi bulkhead must go. It is from a LWB T6 Kombi which has done 115k but it is in good condition internally and only has a few marks on the boot side no cracks though just general...

Standard genuine VW bulkhead with a fixed window. Coming off a single sliding door LWB panel Van. In very good condition (Vans 2019 reg and only travelled 7000 miles). I must admit I'm not entirely sure what these are worth so offers welcome. Seems like the sliding window ones or the motexian...

Hi All, I’m looking to insulate and carpet the back of my van however wondering if anyone has left the lower half of the bulkhead in place and just removed the upper? The van is used for bikes and surfboards so don’t need a step through setup and thought it might make sense to stop things...

As the title says I have a Motexion kombi passenger side single opening bulkhead for sale. I bought this and never used it. Collection. From Telford Shropshire or contact me 07850693532

Hi all, Iam new to the group so hope I have posted this correctly? I am trying to buy a removable bulk head to go behind the second row of seats on a T6 shuttle.I’ve read online a company in Salisbury do this but rang around with no luck. Any help greatly appreciated Thanks

Collection from South Devon As it states, taken out of my T6, It's the metal two part version.

Has been used and was removed recently from my T6 Kombi with twin sliding doors. Overall good condition. ZGB 7H0 017 234 - with carpet/textile & window - fits behind second row seat. Suitable for T5 & T6 Kombi. Window is made from safety glass. Motexion Bulkheads are made from ABS (same...

Hi guys. Thinking about removing the bulkhead to line each side with carpet to deaden the noise from the back of my 67 reg T6 panel van. Has anyone done this and had any success with it? Thanks

Hi, I've decided to take out my kombi bulkhead. My van is a twin slider but the bulkhead looks different on one side so looks to me like it will go in a single. Few marks on the load side £100 collected West Yorkshire

Hi all, Does anyone know if a steel bulkhead removed from a T5.1 panel van will fit straight into a T6 panel van or are the sizes different? I’ve had a look and can’t see that it’s been discussed before … Cheers

Hi all, I’m looking for a bulkhead with window to fit a T6 panel van so that I can keep an eye on the dogs and to let a little extra light into the load area! Preferably within travel distance of Gloucestershire. Cheers

Hi! I have a new fantastic T6 Van Business for my outdoor activities. Windsurfing, Mtb and obviously sleeping. I want to remove the upper part of divider replacing it with a wire mesh behind the driving seat, but VK has not an official mesh. Than I wil put a twinbed that can be transformed in a...

Now gone to the tip.

I've been looking for a shelf to install into my 6.1 Kombi, I was going to go for one of the Forty Winks one's but after speaking to Ryan they won't fit as I have a bulkhead fitted, does anyone know of any off the shelf item that would fit or is the DIY route the only way?