Search results for query: grommet

What CU did you purchase?

...done if you want hook up I would run some arctic cable in conduit now, it’s not that expensive if you buy from an electrical wholesalers and then you can add the CU and sockets later. I put my consumer unit under the bonnet out of the way and used the grommet behind the battery to run the cable.

...van with jet hose plus snow foam and no leak. First bit of rain this morning trickle of water.... (van was parked over night). Cant see the grommet under the dash, there is a grommet under the brake booster in the engine bay with a black pipe going through it but I cant see how its leaking...

There is a rubber grommet behind the steering column, under the dash, hard to see but it’s quite a large grommet. Have a look there.

...support: 2x 1C0 867 388 Rubber strip between grille and bonnet: 2x 7LA 823 707 Side panel indicator repair wire: 2x 000 979 034 E Rubber grommet between windshield washer reservoir and filler neck: 7E0 955 489 With that out of the way let me show you the rest of the process! The van is back...

Hi @Deaky Did you use a buss bar in the mini consumer unit at all?

Pick up the +ve from the starter battery via a suitable fuse, come through the grommet in the bulkhead behind the starter battery to wherever the B2B is located. Pick up a body earth stud close to the charger.

...off, you will need a puller tool though. Pull the plastic cowling off and you can see clearly if the holes are blocked. They aren’t that big so this would be your issue. There is also a large grommet to the right of the steering shaft although these are quite a good fit so I doubt it’s that.

Oh, yes, this brings back memories! Over two years ago!

Yea I do recall searching around a fair bit. There’s a removable panel behind my rear locker. I think that’s how I found access. I used a coat hanger. Attached the end of the cord to the end with electrical tape. And I also used long zip ties to find a path and then pull the wire through.

Thanks, this is encouraging! I have a standard Skyline. Though I'm intrigued how you managed to find the grommet with it being completely boxed in. Did you use rods?

...the ridge all the way to the back. I popped out the round lights to help me move it along - at the back corner it was tricky finding the grommet behind my rear cupboard but I got there - then through the hose into the tailgate - and I brought it back out behind the panel at the base of my...

Handbrake off, then loosen and take the bolt off that cable underneath, then the grommet will slide out of that bracket

...will be post D121 splice) Next Step: 1. Spliced new red wire from T10g plug (grey plug, red wire, Pin 3) in e-box, fed through bottom rubber grommet and zippy tied to harness to G83 sensor 2. Spliced opposite end of red wire onto Pin 1, red wire at G83 sensor 3. Spliced new brown wire from...

...put away- 80% sure the issue was the loose front roof rail. Still waiting on others to input before using the sealant! I’ve found blanking grommets on eBay- various sizes so hopefully straight forward fix on that front. I bought the van converted, paper work shows that Wakefield Van Works...

Thank you Pete I will have a look

There is a grommet through the bulkhead behind the battery, which you can access without removing the battery. Inside the vehicle it is high up above the passengers feet. Have a search on the forum for info. Pete

Yeah, you can see my 240v Victron battery charger to the right. Cables leave the van via the grommet under the drivers seat and are routed in conduit under the body cavity and in through a new hole and grommet into the step area and are all then behind that carpeted ply panel that has the 12v...

...new wire :) I need to solder and put interior trim back tomorrow. Anyone who finds this wanting to do anything in future to the bcm, the grommet under the driver side inspection panel (behind airbox) enters right at the bcm. The BCM wiring is also actually OK to get to, I just removed the...

I bought some little hole plugs off eBay, they look absolutely fine (matte textured finish) and they've stayed in for the last 3k or so. Search for hole plugs or blanking grommets, the ones I got were for 14-21mm holes and they were under a fiver.