I see they give you a few circlips as I’d imagine this will be the part that provokes the most swearing!
Help please Flashing coil light and EML on. Multiple codes 31391 27202 8208 8216 8217 8338
- Thread starter Westcoast888
- Start date
-
- Tags
- fault codes
Diving in!
Charge cooler and bracket out of the way, then it’s the turbo top pipe..
Charge cooler and bracket out of the way, then it’s the turbo top pipe..
Suck the guts out of it with the mityvac so I can get to the linkage…
And it’s out!
Now to adjust the new one to the same dimensions as the old and then refit, which I think is going to be a lot more difficult!
Last edited:
Ok so it’s back on but before I try to fit the circlip the workshop manual is saying to measure voltage via the diagnostic tool. Is this absolutely necessary and if so can vcds do it?
I managed to work out where to do this measurement on vcds. And 0.78v seems to be just right.
Circlip time….
Circlip time….
Last edited:
to check the voltage I opened vcds and then the engine controller. I selected output tests and then turbine actuator IDE07783. I figured this out by myself so it might not be correct but the voltage value changed as I operated the actuator with the mityvac gan
The N/A value will change as you move the actuator.
.
fingers crossed I got it right!
The N/A value will change as you move the actuator..
fingers crossed I got it right!
Stuffed some blue rag in the air pipes in readiness for the flying circlips!
But to be fair it wasn’t too bad and I had success with the 2nd one. God knows where the first one went! Trying to keep the mityvac pumped while manoeuvring some long handled pointy nose pliers with a small screwdriver in your third hand is tricky enough especially in a dark space with crap eyesight!
Last edited:
Part numbers of the old and new actuator
Yes, I believe so.
Just to complement - another way to access would be
VCDS > Select > 01-Engine > Adv. Meas. Values > then pick IDE07783
And the money shot…..
I’m out of MOT atm so just got to change the rear discs and pads and then go for test. I’ll then do a road test and log the values to make sure the turbos are boosting ok. If everything is ok I’ll wrap this up. Hopefully the thread will help others in the future.
Massive thanks to @mmi for all the help in getting to the bottom of it.
Massive thanks to @mmi for all the help in getting to the bottom of it.
Here’s a pic of my other van that I’m using while the newer one is off the road…
so how did you get on?
...
@rajjinator is doing the same job and is having some issues with the actuator length. . .
www.t6forum.com
.
...
@rajjinator is doing the same job and is having some issues with the actuator length. . .
P00AF - 'stuck' with new turbo
Hi all, I have just fitted a new turbo from London Turbos and am getting a fault relating to the actuator position. It's actually in a Crafter, but it's a DAUA engine so relevant in all areas I guess so posting here for better visibility. To cut a long story short, the turbo has been replaced...
.
Sorry for the delay. I’ve changed the rear brake discs and pads, then taken the van for an MOT. It passed with no advisories but I’ve been so busy since I haven’t had the time to take it for a drive. Was hoping to hook up the laptop with vcds on its first test run just to make sure it’s boosting properly. I’ll get to it as soon as poss!so how did you get on?
...
@rajjinator is doing the same job and is having some issues with the actuator length. . .
P00AF - 'stuck' with new turbo
Hi all, I have just fitted a new turbo from London Turbos and am getting a fault relating to the actuator position. It's actually in a Crafter, but it's a DAUA engine so relevant in all areas I guess so posting here for better visibility. To cut a long story short, the turbo has been replaced...
.
