T6 Aftermarket Digital Instrument Cluster
- Thread starter CJW
- Start date
-
- Tags
- digital dash
Mine’s the business pack version but has the lowest spec MFD.
I know I have gone a bit quiet, mainly focussing on getting the Crafter and 6.1 out there - for which I was a large part of the development - but in fact, the Crafter unit is all my fault. They did not know the vehicle existed since they didn't have it in China. So I feel pretty responsible for getting fit perfectly, so I drove up to Grimsby and donated a free fitting to ensure it was right; we had a new firmware on that vehicle developed and installed whilst I was there, I had them on tap doing the night shift to rectify any faults.
It's been seamless since
BUT... This!! EVEREST-VW DIGIDASH CONNECTED - HEAD UNIT SYNC KIT: (Connect Box, Link
I dont like to blow my trumpet; that's not me, but there isn't another connect box, let alone a kit that won't end up on eBay once you've tried this! I know of several already.
If you don't like it for whatever reason, you can send it back to me in perfect condition within 21 Days for a full refund as a T6 Forum Special; just PM me through the site, and I will put a note on your order - Owsat! The first two batches are nearly sold out, and I have ordered enough stuff to build 100 kits on the way to me. Yikes! Kind of.. but genuinely. I haven't got the money to burn on bad investments. This is a standout product! So I put my name on it! Since these are going to be getting shown off!
Thanks for everyone's support in getting to this stage! It's only possible with the collective thoughts of the many! Like most things that go on in here!
Ant
It's been seamless since
BUT... This!! EVEREST-VW DIGIDASH CONNECTED - HEAD UNIT SYNC KIT: (Connect Box, Link
I dont like to blow my trumpet; that's not me, but there isn't another connect box, let alone a kit that won't end up on eBay once you've tried this! I know of several already.
If you don't like it for whatever reason, you can send it back to me in perfect condition within 21 Days for a full refund as a T6 Forum Special; just PM me through the site, and I will put a note on your order - Owsat! The first two batches are nearly sold out, and I have ordered enough stuff to build 100 kits on the way to me. Yikes! Kind of.. but genuinely. I haven't got the money to burn on bad investments. This is a standout product! So I put my name on it! Since these are going to be getting shown off!
Thanks for everyone's support in getting to this stage! It's only possible with the collective thoughts of the many! Like most things that go on in here!
Ant
just received mine and got it up an running, Very impressed! the screen quality is superb. Only issue I have is apparently there is a speed warning set at 59 mph somehow, even though the setting seems to be off... is this the multiple down/ok thing???
@antony.charnley you have an Alpine Halo in your van so all the videos are with that, so I am a little confused still about what the system looks like / works like with a discover media pro head unit. Have you installed any with this yet? Thanks
frankKufstein
Member
In the Menue ( “calibration” if I remember right ) scroll down to reboot and confirm rebooting
Then the speed warning should be gone
Doubt that disconnect the battery for 20 mins that's sorts it
frankKufstein
Member
Where did i write to disconnect the Battery ?
You didn't write it but what you have wrote doesn't work for everyone but disconnecting thr battery does
What vehicle ?
If you had a T6 Highline cluster 100% follow my guide on how to clear speed alerts on my website in the FAQ section.
If you have a 6.1 you should clear in advance from the head unit settings under vehicle. Then you multi function steering controls can never touch it.
Startline I believe the 5*((down and ok)*9 times, then right) should fix you.
If you have a 6.1 you should clear in advance from the head unit settings under vehicle. Then you multi function steering controls can never touch it.
Startline I believe the 5*((down and ok)*9 times, then right) should fix you.
Please could you elaborate on this Startline sequence Antony? Not seen this before.
It's not perfect but the algebra is there: try..
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
It's the same as a terminal disconnect. I also have this feeling that the Reboot command at the bottom of the Configuration menu might stock set the BCM. But that I have not fully confirmed yet, it behaves in a similar way. Probably, it just changes the way the virtual reboots, but it clears lingering messages and I think helps clear cache following firmware run in.
Tricky conversations to have with China since half the time they don't know what I'm on about..
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
Down, ok (repeat 9 times)
Right
It's the same as a terminal disconnect. I also have this feeling that the Reboot command at the bottom of the Configuration menu might stock set the BCM. But that I have not fully confirmed yet, it behaves in a similar way. Probably, it just changes the way the virtual reboots, but it clears lingering messages and I think helps clear cache following firmware run in.
Tricky conversations to have with China since half the time they don't know what I'm on about..
@antony.charnley I've just saw your YT
fro T6.1 - will this work also for T6?
My button press sequence on my site does the same for T6 highline. Not an infotainment oem feature unfortunately.
I've just had a peculiarity. Was very nearly out of fuel, van had been in the red for ages, when the bottom segment of the fuel display is all shaded red. Was on fumes. Stopped for fuel, filled up. When I restarted the gauge needle goes to the top of the fuel gauge as expected, bottom third or so stays highlighted shaded red and the bongs are back!
After next restart 20 mins or so later, fuel gauge is back to normal, but the bongs are back. Just tried the 9X etc.. Not worked. Will try the 2X, 8X, right etc., as on Everest's web site when I get moment. I'm still on the original code the thing came with back in December.
After next restart 20 mins or so later, fuel gauge is back to normal, but the bongs are back. Just tried the 9X etc.. Not worked. Will try the 2X, 8X, right etc., as on Everest's web site when I get moment. I'm still on the original code the thing came with back in December.
The 9x method doesen‘t work for me too!
I tried it on my benchsetup and with 9x method I got this:
Then I tried this one from the technician:
And it always works!
I think that’s right:
4 rounds without ACC
5 rounds with ACC
6 rounds for MQB vehicles
Similar threads
